Electrical Safety Engineering of Renewable Energy Systems. Rodolfo Araneo
m, laying on a surface of resistivity ρ. The expression in ohms of the ground resistance Rf of such electrode is given in Eq. 1.16.
If we assume that the two feet act as ground electrode in parallel, and that the plates do not interfere with each other, the body resistance-to-ground RBG equals 1.5ρ.
In general, it may be conservatively assumed that the person does not wear shoes or gloves, and that there is no floor to limit the body current. However, standard EN 505227 allows, for calculation purposes, additional known resistances in series to the body resistance (e.g., gloves, footwear, standing surface made of insulating material, such as gravel, asphalt, etc.); EN 50522 identifies in 1 kΩ the average value for old and wet shoes. Typical shoe resistances are 5–10 kΩ for wet leather soles, 100–500 kΩ for dry leather soles, and 20 MΩ for rubber soles.
To calculate the body current, we determine the parameters of a Thevenin equivalent circuit, Vth (i.e., equivalent voltage source) and Rth (i.e., equivalent resistance), as seen from the point of contact of the body with the energized part, and the ground (Figure 1.13).
Figure 1.13 Equivalent circuit for the computation of body currents due to a touch voltage.
Rth is generally negligible if compared to RB +RBG, and therefore can be conservatively ignored; the fault source can be thought of as an ideal voltage generator.
In these conditions, the body current iB can be calculated with Eq. 1.17.
In Figure 1.12, VST. is the prospective touch voltage, which is defined as the potential difference between simultaneously accessible conductive parts, when those conductive parts are not being touched by a person. VT is the (effective) touch voltage, defined as the potential difference between accessible conductive parts when touched simultaneously by a person (one part can be the ground) [23–27]. The value of the effective touch voltage is affected by the persons’ body resistance, greatly variable, and the person’s resistance-to-ground. Consequently, the same touch voltage may correspond to different body currents, and this makes the touch voltage a rather ineffective indicator of hazard. Thus, for the purpose of designing protective measures against electric shock, technical standards identify a conventional body resistance of 1 kΩ.
The step voltage is defined as the voltage between two points on the earth’s surface that are 1 m distant from each other, which is considered the standard stride length of a person.
In the worst-case scenario, prospective touch voltages may equal the ground potential rise VG. To better clarify the concept, let us assume that in the event of a fault, a hemisphere of radius r0 , and resistance-to-ground RG leaks to ground the current i. Let us also assume a person standing in a region at zero potential; the person is touching a metallic structure electrically connected to the hemisphere for grounding purposes (Figure 1.14).
Figure 1.14 Person standing in a region at zero potential.
The hemisphere attains the ground potential rise VG = iRG, and so does the metallic structure: the person’s hand is at the potentialVG, whereas their feet are at zero potential. The prospective touch voltage VST equals the ground potential rise; however, the effective touch potential VT is a lower value, equal to the voltage drop on the person’s body resistance RB, as established by the voltage divider between RB and RBG (Figure 1.13).V(r) over the soil is shown in Figure 1.15. It can be seen that in correspondence with the persons’ feet, the surface ground-potential rises up from (almost) zero to the value VBG, which accordingly lowers the touch voltage.
Figure 1.15 Distribution of the ground-potential with a person standing in a region at zero potential.
The other possible scenario is the person standing in a non-zero potential region, at a distance r from the center of the hemisphere less than 5r0 (Figure 1.16).
Figure 1.16 Distribution of the ground-potential with person standing in a region at non-zero potential.
In this case, the prospective touch voltage VST is less than VG, even though the person’s hand is still at the potential VG. The person’s feet, in fact, will be at a higher potential, with an evident reduction of both prospective and touch voltage.
A possible hazardous situation is when the person, although standing in a non-zero potential area, may also be in contact with a conductive part at zero potential. Such parts, defined as Extraneous-Conductive-Parts (EXCPs) [28, 29], may include water pipes, exposed metallic structural parts of the building, etc.
EXCPs may have a very low resistance-to-ground REx, such that REx<<RBG. therefore, if contacted, they may completely bypass the person’s body resistance-to-ground. The person is therefore subjected to a greater touch voltage, and if REx were zero, the touch voltage would equal VST (Figure 1.17).
Figure 1.17 Equivalent circuit for the computation of body currents in the presence of an EXCP.
Example 1.1 A hemispherical electrode of radius r0 = 2 m is buried in the ground of resistivity ρ = 200 Ω m and connected to a tower crane (Figure 1.13). A person is standing 10 m away from the center of the hemisphere and holding a metal hook electrically connected to the hemisphere. A ground-fault causes a current i = 100 A to flow into the earth through the hemisphere. Determine the electric current iB through the person’s body in the case of touch, assuming a conventional body resistance of 1 kΩ.
Solution
From Eq. 1.9, the ground potential rise of the hemisphere is:
The touch voltage is V(r0)–V(r), where V(r) can be calculated with Eq. 1.8 with r = 10 m.