Standard Catalog of Civil War Firearms. John F. Graf
Though records do not specifically indicate pattern models, it is very likely that both Confederate and U.S. Ordnance purchasing agents obtained P39 muskets.
| GOOD–$920 | FINE–$1,350 |
BRITISH PATTERN 1842 MUSKET, .76 CALIBER, PAPER CARTRIDGE, PERCUSSION
Made by various English manufactures, London, England, 1842-1855. Total imported: Unknown, but likely several thousand.
Overall length: 55".
Muzzleloader, single shot.
Lock plates vary depending on year of manufacture. Generally, the lock plate will be stamped with a crown over “VR”, the British “broad arrow” and the year of manufacture in addition to “Enfield” or “Tower”, depending on place of manufacture. Barrels are stamped with either the Enfield proof mark, a crown over “VR” or “MR” above a set of crowned scepters or the London and Birmingham mark consisting of a crown over “TP” over a broad arrow in addition to a crown over “B” surmounting a “7” over a crowned broad arrow.
The P42 musket can be recognized by the three flat keys and upper swivel screw that retain the barrel to the stock. The P42 was produced with a notched rear sight. The ramrod head is slightly concave. Rather than a side plate like that found on the P39, the lock plate screws pass through two brass washers with rectangular extensions on opposite sides. Though records do not specifically indicate pattern models, it is very likely that both Confederate and U.S. Ordnance purchasing agents obtained P39 muskets.
| GOOD–$950 | FINE–$1,350 |
CONFEDERATE CONTRACT PERCUSSION CONVERSIONS
Converted by various gunsmiths, Richmond, Virginia, 1861. Total production: 50,000.
Muzzleloader, single shot.
In 1861, the Commonwealth of Virginia contracted six Richmond gunsmiths to convert approximately 50,000 flintlock muskets: S.B. Cocke, Thomas Addams Jr., Francis Perpignon, Samuel C. Robinson, Samuel Sutherland, and the Union Manufacturing Company. The contractors all employed the brazed bolster configuration.
James D. Julia Auctioneers, Fairfield, Maine
James D. Julia Auctioneers, Fairfield, Maine
Confederate Brazed Bolster, Type I. Percussion bolster brazed over the flintlock vent. An iron plug blocks the hole drilled through the bolster to connect the cone hole to the old vent hole.
James D. Julia Auctioneers, Fairfield, Maine
Confederate Brazed Bolster, Type II. Percussion bolster brazed over the flintlock vent. A screw blocks the hole drilled through the bolster connect the cone hole to the old vent hole.
The “Confederate brazed bolsters” do not add significantly to the value of the particular converted musket. For values, refer to the particular type of weapon.
U.S. MUSKET, .69 CALIBER, CONTRACT CONVERSIONSTO PERCUSSION IGNITION
W hen the U.S. Ordnance Department determined to convert its firearms from flintlock to percussion ignition systems in the 1840s, it had 600,000 muskets deemed suitable for altering to percussion. Many of those muskets were converted from the late 1840s until the beginning of the Civil War, using three basic systems:
James D. Julia Auctioneers, Fairfield, Maine
The French-style (or side-lug, or drum-and-nipple).
This was the earliest type of conversion and was performed by private contractors until the early 1850s. All exposed lock parts were removed, the flash pan cut and ground off almost flush with the lock plate, the touch hole enlarged, and screw holes plugged. A cylindrical bolster and nipple was screwed into the touch hole and a new hammer installed.
| GOOD–$700 | FINE–$1,300 |
James D. Julia Auctioneers, Fairfield, Maine
Virginia cone-in-barrel contract conversion. James D. Julia Auctioneers, Fairfield, Maine
New York State Hitchcock contract cone-in-barrel conversion.
The Belgian-style (or cone-type). This conversion, performed insofar as is known by only the national armories in the early 1850s, involved removing all exposed lock components, filling screw holes, and removing the pan and filling the resulting hole with brass, flush with the lock plate surface. A nipple was screwed into a threaded hole near the top of the barrel, slightly right of center, and a new hammer installed.
| GOOD–$700 | FINE–$1,300 |
Hewes & Phillips style of bolster conversion. James D. Julia Auctioneers, Fairfield, Maine
New Jersey Patent Breech (Type I) bolster alteration. James D. Julia Auctioneers, Fairfield, Maine
New Jersey Patent Breech (Type II) bolster alteration. James D. Julia Auctioneers, Fairfield, Maine
Leman Pennsylvania contract bolster conversion. James D. Julia Auctioneers, Fairfield, Maine
Butterfield Pennsylvania contract bolster conversion. James D. Julia Auctioneers, Fairfield, Main
Virginia Manufactory bolster conversion. James D. Julia Auctioneers, Fairfield, Maine