Packaging Technology and Engineering. Dipak Kumar Sarker
of moulded shapes for volumes ranging from 190 to 500 ml. A higher specification for exact hues in pharmaceutical‐grade tinted glass, which is not essential in food packs, lies behind the higher cost of flint over coloured glass; this is also different from food product glasses, in which recycled glass use of differing tints is commonplace.
Type I glass is suitable as a packaging material for most parenteral or non‐parenteral pharmaceutical products and is the pharmacy primary packaging standard because of its inertness and thermal stability. This type of glass possesses the highest Tm values and so is much harder to work and shape to the desired form. The chemical robustness of borosilicate means that the glass is also ideally suited to the containment of strong acids and alkalis. Type II glass containers based on soda lime/silica glass (type III) but treated via a surface‐inactivation process to provide a contact surface that has remnant alkali ions removed is suitable for most acidic or neutral aqueous medicinal preparations, whether for parenteral or non‐parenteral use. The modification of the regular soda lime glass surface with sulfur creates a material with excellent resistance to surface hydrolytic reactions that typically occur with the ageing and weathering of glass. Modification of type III glass in this way to produce type II glass removes the sodium and calcium oxides that can be leached from water in contact with the glass surface, thereby preventing weathering and blooming from bottles. Weatherisation and ‘bloom’ formation refer to haze or visual crystalline carbonate (Na2CO3 is the most abundant but it may also contain also CaCO3) found on the inside of plain soda lime glass. Its appearance can alarm consumers, who mistake the clouding for possible microbial contamination and growth. The effect of weatherisation is actually minimal upon the overall quality of the glass but sodium carbonate can influence the pH of the contacting solution according to the glass formulation chemistry and solvent contact time. The hygroscopic nature of soda lime glass means that water films can easily form and accumulate on the glass surface; this happens particularly on the inside surface, where there may be water‐containing product and therefore intrinsic water vapour. Moist conditions and changes in relative humidity driven by variations in temperature, during, for example, sea freight shipping, can affect the amount of atmospheric moisture that the glass is exposed to during storage and shipment, leading to an alternating process of condensation and evaporation. Such surface adsorption can induce the dissolution of glass‐borne Na+ and Ca2+ ions, which then reform as water‐dispersible carbonate crystals on the surface of the glass in the presence of carbon dioxide and as the glass surface dries. Such carbonate frosting can disappear or dissolve. Treating the surface of the glass with fluorine gas can make the surface of the glass 10 times more chemically inert and therefore less susceptible to bloom formation.
The lower Tm of type II glass compared with borosilicate glass means that bottles require a lower temperature to be blown and injection‐moulded. Regular soda lime glass (type III) is an untreated version of soda lime glass that is routinely used for foods, with average chemical resistance based around an average chemical composition of 75% silica, 15% sodium oxide (soda), and 10% calcium oxide (lime) but with small additional amounts of aluminium oxide (alumina), magnesium oxide (magnesia), and potassium oxide (potash). Alumina is incorporated to positively influence the chemical durability of the glass and magnesia is used as an agent to lower the overall Tm on the addition of alumina (Tm ∼ 2070 °C), which serves to reduce the temperature required for moulding operations. Type III glass containers are occasionally used as packaging material for parenteral products or powders for parenteral use but only in instances where stability testing data indicate their suitability. This type of glass is, however, used routinely for food products and as the packaging for non‐aqueous and non‐parenteral pharmaceutical preparations. This type of glass is preferred over type IV material and is used for products that need to be autoclaved as it demonstrates a resistance to the erosion reactions and the increased rate instigated by high‐temperature treatment of the glass container. Type IV glass containers (general purpose soda lime glass) or non‐pharmaceutical and non‐parenteral lower grade general application soda lime glass are used universally as the packaging for foods and beverages, where their low hydrolytic resistance is not an issue. Other than food uses, type IV glass containers have applications in the containment of skin creams and topical products or for oral dosage forms, such as food supplements. With lower grades of glass, delamination of the material in pharmaceutical vials is important, as in other sterile products, and negates its use because it can provide a route for microbe entry into the product by permitting the ingress of air [13].
The standard composition of plain, transparent, ‘everyday use’ or general purpose soda glass is shown in Figure 2.4. This is the glass used for conserve jars, clip‐down Kilner jars, beer and wine bottles, and pâté‐like spread jars all blow‐moulded at pressures of 0.28–0.32 MPa (atmospheric pressure). This type of glass is primarily made of fine ground silica (SiO2) at about 70%. The glass also contains soda (Na2O) or sodium sulfate as the next biggest component at about 14%, or a blend of the two. Lime (CaO) is present at about 10% as a modifier. Magnesia (MgO) and alumina (Al2O3) are present at approximately 3% and 2%, respectively. Other ingredients such as iron oxides and potash (K2O) are present at 0.7% and 0.3%, respectively. Glass is an amorphous structure made of a complex entwinement and association in lamellae of a basic monomeric unit, which is the sodium, potassium, and calcium silicate lattice formed at temperatures in excess of 1300 °C (normal glass‐making temperature is 1580 °C). The molecular structure of glass is still somewhat of a complex and not yet fully understood subject, but the basic unit of the component and process variable and large ‘sprawling’ molecule might be (−(xR2O.SiO2)n(yR′O.SiO2)n(zR′′2O3.SiO2)n‐)n, where R, R′, and R′′ represent monovalent (Na, K, Li), divalent (Ca, Co, Fe, Pb), and trivalent (Al, Fe) ion species, respectively, which may or may not be present. In this molecular formula n is a variable number, and x, y, and z represent stoichiometric ratio values sufficient to combine in exact molar proportions with oxygen (O). The molecules are bonded together on cooling in a ‘loose’ form but with an immense viscosity (customarily 0.8–1.5 × 1018 Pas; with extremes of 1018–1021 Pas for speciality glasses). Molten glass has a viscosity of 1000 kPas to 0.1 kPas between 800 °C and 1580 °C, respectively, which is somewhere between that of room temperature butter and glycerine syrup. The glass transition temperature (Tg), which is analogous to ‘melting’, of this amorphous solid is typically in the approximately 580–1125 °C range, depending on the type of glass, and it has a viscosity of approximately 1014 Pas at 525 °C, which is below the Tg. Any glass can be considered to be a ‘frozen liquid’ in the supercooled state, in which the components do not return to their original form, which prevents extensive ordering and significant crystallinity, and, therefore, means that glasses do not possess a clear Tm. Combinations of starch or water‐dispersible colloidal polymers and water also form glassy materials at room temperature (see Sections 3.2 and 8.8.1). There are many naturally occurring mineral glasses and all are formed as a result of subterranean igneous processes. In fact, it is thought that the original use of glass stems from the naturally occurring material. Conventional glass‐making uses a combination of virgin ingredients and recycled broken or shredded glass, called cullet, incorporated at approximately 25% w/w on average but this can range from 17% to 93%. This reuse has the advantage of requiring lower process temperatures and, therefore, it has a cheaper and less polluting manufacturing cycle [14]. Making glass is thought to generate between 500% and 600% in carbon dioxide of the weight of silicates and additives used to make the final glass. However, the process is still marginally less polluting than steel or aluminium refining.
References
1 1 Environmental Protection Agency. (2016). Documentation for Greenhouse Gas Emission and Energy Factors Used in the Waste Reduction Model: Containers, Packaging, and Non‐Durable Good Materials Chapters, 1–82. USA: ICF, for the US Environmental Protection Agency,