Welding Metallurgy. Sindo Kou
and yet stable arc as in GTAW is not required. However, GMAW guns can be bulky and difficult to reach small areas or corners.
1.3.5 Flux‐Cored Arc Welding
1.3.5.1 The Process
FCAW is similar to GMAW and the GMAW machines can be used. However, the wire electrode is flux cored rather than solid; that is, the electrode is a metal tube with flux wrapped inside. The functions of the flux are similar to those of the electrode covering in SMAW, including protecting the molten metal from air. The use of additional shielding gas is optional as shown in Figure 1.21.
Figure 1.21 Flux‐cored arc welding: (a) overall process; (b) welding area enlarged.
Figure 1.22 compares gas shielding in several arc welding processes. In SMAW and FCAW, the decomposition of the flux produces the shielding gas right at the arc and next to the weld pool. Thus, even when welding in the presence of flowing air, such as winds in field welding, the shielding gas can still protect the molten metal reasonably well. In GMAW and GTAW, however, the shielding gas may be blown away by winds immediately after exiting the gas nozzle. The molten metal may not be protected effectively by the shielding gas.
Figure 1.22 Sensitivity of gaseous shield of molten metal to wind or draft.
1.3.6 Submerged Arc Welding
1.3.6.1 The Process
SAW is a process that melts and joins metals by heating them with an arc established between a consumable wire electrode and the metals, with the arc being shielded by a molten slag and granular flux, as shown in Figure 1.23. This process differs from the arc welding processes discussed so far in that the arc is submerged and thus invisible. The flux is supplied from a hopper, which travels with the torch. No shielding gas is needed because the molten metal is separated from the air by the molten slag and granular flux. DCEP is most often used. However, at very high welding currents (e.g. above 900 A), AC is preferred in order to minimize arc blow. Arc blow is caused by the electromagnetic (Lorentz) force as a result of the interaction between the electric current itself and the magnetic field it induces.
Figure 1.23 Submerged arc welding: (a) overall process; (b) welding area enlarged.
1.3.6.2 Advantages and Disadvantages
The protecting and refining action of the slag helps produce clean welds in SAW. Since the arc is submerged, spatter and heat losses to the surrounding air are eliminated even at high welding currents. Both alloying elements and metal powders can be added to the granular flux to help control the weld metal composition and increase the deposition rate, respectively. Using two or more electrodes in tandem further increases the deposition rate. Because of its high deposition rate, workpieces much thicker than that in GTAW and GMAW can be welded by SAW. However, the relatively large volumes of molten slag and metal pool often limit SAW to flat‐position welding and circumferential welding (of pipes). The relatively high heat input can reduce the weld quality and increase distortions.
1.3.7 Electroslag Welding
1.3.7.1 The Process
ESW is a process that melts and joins metals by heating them with a pool of molten slag held between the metals and continuously feeding a filler wire electrode into it, as shown in Figure 1.24. The weld pool is covered with molten slag, and it moves upward as welding progresses. A pair of water‐cooled copper shoes, one in the front of the workpiece and one behind it, keeps the weld pool and the molten slag from breaking out. Similar to SAW, the molten slag in ESW protects the weld metal from air and refines it. The arc exists only during the initiation period of the process, that is, when the arc heats up the flux and melts it. The arc is then extinguished, and the resistance heating generated by the electric current passing through the slag keeps it and the weld pool from freezing. In order to make heating more uniform, the electrode is often oscillated, especially when welding thicker sections. Figure 1.25 is the transverse cross section of an electroslag weld in a steel 7 cm thick [13]. Typical examples of the application of ESW include the welding of ship hulls, storage tanks, and bridges.
Figure 1.24 Electroslag welding: (a) overall process; (b) welding area enlarged.
Figure 1.25 Transverse cross section of electroslag weld in 70‐mm‐thick steel.
Source: Eichhorn, Remmel, Wubbels [13]. Welding Journal, January 1984, © American Welding Society.
1.3.7.2 Advantages and Disadvantages
ESW can have extremely high deposition rates, but only one single pass is required, no matter how thick the workpiece is. Unlike SAW or other arc welding processes, there is no angular distortion in ESW because the weld is symmetrical with respect to its axis. However, the heat input is very high, and the weld quality can thus be rather poor, including low toughness caused by coarse grains in the fusion zone and HAZ. ESW is restricted to vertical position welding because of the very large pools of the molten metal and slag.
Cary [14] summarized the deposition rates of various arc welding processes. The deposition rate increases in the order of GTAW, SMAW, GMAW and FCAW, SAW, and ESW. The deposition rate can be much increased by adding iron powder in SAW or using more than one wire in SAW, ESW, and GMAW.
1.4 High‐Energy‐Beam Welding
1.4.1 Electron Beam Welding
1.4.1.1 The Process
EBW is a process that melts and joins metals by heating them with an electron beam. Arata [15] was a pioneer in high‐energy‐beam welding processes such as electron‐ and laser‐beam welding. As shown in Figure 1.26a, the cathode of the electron beam gun is a negatively charged filament. When heated up to its thermionic emission temperature, this filament emits electrons. These electrons are accelerated by the electric field between a negatively charged bias electrode (located slightly below the cathode) and the anode. They pass through the hole in the anode and are focused by an electromagnetic coil to a point at the workpiece surface. The beam current and the accelerating