Integration of Renewable Energy Sources with Smart Grid. Группа авторов
Any leftover water and condensed steam are injected back into the reservoir, making this a sustainable resource.
3 (iii) Binary Steam: Binary cycle power plants operate on water at lower temperatures of about 225°F–360°F (107°C–182°C). Binary cycle plants use the heat from the hot water to boil a working fluid, usually an organic compound with a low boiling point. The working fluid is vaporized in a heat exchanger and used to turn a turbine. The water is then injected back into the ground to be reheated. The water and the working fluid are kept separated during the whole process, so there are little or no air emissions.Currently, two types of geothermal resources can be used in binary cycle power plants to generate electricity: enhanced geothermal systems (EGSs) and low-temperature or co-produced resources [13].a) Enhanced Geothermal Systems:EGS provide geothermal power by tapping into the Earth’s deep geothermal resources that are otherwise not economical due to lack of water, location, or rock typeb) Low-Temperature and Co-Produced Resources:Low-temperature and co-produced geothermal resources are typically found at temperatures of 300°F (150°C) or less. Some low-temperature resources can be harnessed to generate electricity using binary cycle technology. Co-produced hot water is a by-product of oil and gas wells in the United States. This hot water is being examined for its potential to produce electricity, helping to lower greenhouse gas emissions and extend the life of oil and gas fields.
1.1.6.1 Geothermal Provinces of India
In India, nearly 400 thermal springs occur (Satellites like the IRS-1 have played an important role, through infrared photographs of the ground, in locating geothermal areas. The Puga valley in the Ladakh region has the most promising geothermal field.), distributed in seven geothermal provinces. These provinces include The Himalayas: Sohana: West Coast; Cambay: Son-Narmada-Tapi (SONATA): Godavari and Mahanadi [14].
These springs are perennial and their surface temperature range from 37°C to 90°C with a cumulative surface discharge of over 1,000 L/m. The provinces are associated with major rifts or subduction tectonics and registered high heat flow and high geothermal gradient. For example, the heat flow values and thermal gradients of these provinces are 468 mW/m2; 234°C/km (Himalayas); 93 mW/m2; 70°C/km (Cambay); 120–260 mW/m2; 60–90°C/km (SONATA); 129 mW/m2; 59°C/km (West Coast); 104 mW/m2; 60°C/km (Godavari) and 200 mW/m2; 90°C/km (Bakreswar, Bihar).
The reservoir temperature estimated using the above described geothermometers are 120°C (West Coast), 150°C (Tattapani), and 200°C (Cambay). The depth of the reservoir in these provinces is at a depth of about 1 to 2 km.
These geothermal systems are liquid dominated and steam dominated systems prevail only in Himalayan and Tattapani geothermal provinces. The issuing temperature of water at Tattapani is 90°C, at Puga (Himalaya) is 98°C, and at Tuwa (Gujarat) is 98°C. The power-generating capacity of these thermal springs is about 10,000 MW (Ravi Shanker, 1996). These are medium enthalpy resources, which can be utilized effectively to generate power using binary cycle method.
Since majority of these springs are located in rural India, these springs can support small-scale industries in such areas. Dehydrated vegetables and fruits have a potential export market and India being an agricultural country, this industry is best suited for India conditions.
Map of India showing the geothermal provinces, heat flow values (mW/m2: in italics) and geothermal gradients (°C/km). I: Himalaya; II: Sohana; III: Cambay; IV: SONATA; V: West Coast; VI: Godavari; VII: Mahanadi. M: Mehmadabad; B: Billimora.
All the geothermal provinces of India are located in areas with high heat flow and geothermal gradients. The heat flow and thermal gradient values vary from 75–468 mW/m2 and 59–234°C, respectively. Deep Seismic Sounding (DSS) profiles were carried out across several geothermal provinces (Son-Narmada-Tapi; West Coast and Cambay) to understand the crustal structure.
References
1. Akbarali, M.S., Subramanium, S.K., Natarajan, K., Real and Reactive Power Control of SEIG Systems for Supplying Isolated DC Loads. J. Inst. Eng. India Ser. B, 99, 587–595, 2018, https://doi.org/10.1007/s40031-018-0350-8.
2. Akbarali, M.S., Subramanium, S.K., Natarajan, K., Modeling, analysis, and control of wind-driven induction generators supplying DC loads under various operating conditions. Wind Eng., pp. 1–16, 2020, https://doi.org/10.1177/0309524X20925398.
3. Yuldoshevb, A., Shoguchkarova, S.K., Kudratov, A.R., Jamolov, T.R., A Study of the Parameters of a Combined Photo-Thermoelectric Installation under Field Conditions. Appl. Sol. Energy, 56, 2, 125–130, 2020.
4. Joardder, M.U.H., Halder, P.K., Rahim, M.A., Masud, M.H., Solar Pyrolysis: Converting Waste Into Asset Using Solar Energy, in: Clean Energy for Sustainable Development, M.G. Rasul, A. k. Azad, S.C. Sharma (Eds.), pp. 213–235, Academic Press, United Kingdom, 2017, https://doi.org/10.1016/B978-0-12-805423-9.00008-9.
5. Prem Kumar, T., Naveen, C., Premalatha, M., Performance Analysis of 2 in 1 Parabolic Trough Collector for Both Hot Water and Hot Air Production for Domestic Household Applications. Appl. Sol. Energy, 55, 397–403, 2019.
6. Qandil, H., Wang, S., Zhao, W., Application-based design of the Fresnel lens solar concentrator. Renewables: Wind, Water, Solar, 6, 3, 1–13, 2019.
7. Badal, F.R., Das, P., Sarker, S.K. et al., A survey on control issues in renewable energy integration and microgrid. Prot. Control Mod. Power Syst., 4, 8, 2019.
8. Agarwal, V., Aggarwal, R.K., Patidar, P., Patki, C., A novel scheme for rapid tracking of maximum power point in wind energy generation systems. IEEE Trans. Energy Convers., 25, 1, 228–36, 2010.
9. Bridgwater, A.V., Review of fast pyrolysis of biomass and product upgrading. Biomass Bioenergy, 38, 68–94, March 2012.
10. Orozco, R., Redwood, M.D., Yong, P., Cadellari, I., Towards an integrated systems for Bio-energy: Hydrogen production for Escherichia Coil and use of palladium coated waste cells for electricity generation in a fuel cell. Biotechnol. Lett., 32, 12, 1837–45, December 2010.
11. Picarelli, A. and Vargiolu, T., Optimal management of pumped hydroelectric production with state constrained optimal control. J. Econ. Dyn. Control. in press, corrected proof Available online 10 June 2020, 103940, vol. 126, pp. 1–24, May 2021.
12. Majorowicz, J. and Grasby, S.E., Deep geothermal energy in Canadian sedimentary basins VS. Fossils based energy we try to replace – Exergy [KJ/KG] compared. Renewable Energy, 141, 259–277, October 2019.
13. Pollack, A. and Mukerji, T., Accounting for subsurface uncertainty in enhanced geothermal systems to make more robust techno-economic decisions. Appl. Energy, 25415, 113666, November 2019.
14. Van Erdeweghe, S., Van Bael, J., Laenen, B., D’haeseleer, W., Optimal configuration for a low-temperature geothermal CHP plant based on thermoeconomic optimization. Energy, 17915, 323–335, July 2019.
1 *Corresponding author: [email protected]
2
Present Power Scenario in India
Niraimathi R.1*, Pradeep V.2, Shanthi M.3 and Kathiresh M.4
1Department of EEE, Mohamed Sathak Engineering College, Kilakarai, India
2Department of EEE, Alagappa Chettiar College of Engineering and Technology, Karaikudi, India