Reservoir Characterization. Группа авторов
target="_blank" rel="nofollow" href="mailto:[email protected]">[email protected]
2
A Comparison Between Estimated Shear Wave Velocity and Elastic Modulus by Empirical Equations and that of Laboratory Measurements at Reservoir Pressure Condition
Haleh Azizia1*, Hamid Reza Siahkoohi2, Brian Evans3, Nasser Keshavarz Farajkhah4 and Ezatollah KazemZadeh4
1Department of Geophysics, Science and Research Branch, Islamic Azad University, Tehran, Iran
2Institute of Geophysics, University of Tehran, Tehran, Iran
3Department of Petroleum Engineering, Curtin University, Perth, Australia
4Research Institute of Petroleum Industry, Tehran, Iran
Abstract
The objective of this study is to assess the accuracy of the empiricalequations in estimating the shear wave velocity and elastic modulus of rock sample at reservoir pressure condition. The evaluated relations are Gassman, Greenberg and Castagna which have been in use by researchers for a long time and have shown acceptable results. The plug sample investigated in this study is taken from Berea sandstone reservoir southwest of Australia, which is a known reference sandstone for this type of study. This plug in the laboratory was flooded with supercritical carbon dioxide fluid, saturated and pressured under axial, radial and pore pressure comparable to oil reservoirs pressures, after which elastic wave velocity and elasticity modules were determined. Then, using empirical relationships such as Gassman, Greenberg and Castagna and measured values of P-wave velocity, shear wave velocity, and elasticity coefficients were estimated. Comparison of theoretical values versus experimental values shows they compare very well, only in some cases a difference between estimated and experimental values for the coefficients of elasticity has been observed. We believe that the difference is due to the assumptions that were made in those theories. The shear wave modulus didn’t remain constant during fluid saturation. Also, the measured bulk modulus and the calculated values based on Gassman formula did not compare very well. This difference was observed to be larger at higher pressures.
Keywords: Wave velocity estimate, elastic waves, the coefficients of elasticity, rock physics, reservoir conditions, Gassman relations, Greenberg – Castagna theory, injecting carbon dioxide, sandstone
2.1 Introduction
Study of propagation of shear and compressional waves give useful information and constitutional characteristics of hydrocarbon reservoirs, such as lithology and pore fluid type. This information is very important for reservoir development and recovery, and especially for future decision making. On the other hand, the behavior of reservoir rocks geomechanics, play an important role in the design and implementation of drilling, production planning and sustainability of oil and gas wells.
Having physical geology information such as density, porosity, compressional and shear wave velocities are required to successfully perform the above-mentioned projects. This is usually the case that the information about shear wave velocity is not readily available compared with other data. Therefore, theoretical or experimental approaches are necessary to estimate this velocity.
In geomechanical evaluation of hydrocarbon reservoirs, several methods can be used to estimate shear wave velocity and elastic constants. Conventional methods for estimating the shear wave velocity can be divided into five categories which are [1–3]: laboratory measurements, direct measurements, empirical relationships, the regression method and the intelligent method (Figure 2.1).
Figure 2.1 Common methods for estimating the shear wave velocity.
Each of these methods has its own unique advantages that make it suitable to estimate the shear wave velocity. The dependency of wave propagation velocity to lithology, porosity, temperature, pressure and type of pore fluid, has introduced a variety of investigation methods in geophysics and rock physics.
Laboratory measurement of shear wave velocity in a core is known as a standard procedure and the obtained velocities are comparable with that of the other methods. There are other field methods to estimate shear wave velocity such as Dipole Shear Sonic Imager and sonic logs. Although these methods are common, they must be performed in a large number of wells to obtain the velocity distribution in the entire field, and core extraction or running of sonic tools in a large field is very expensive [4]. Another common method to estimate the shear wave velocity is based on theoretical evaluation and modeling. In the past few decades, several empirical formulas have been introduced for estimating the shear wave velocity in rocks with different lithology, based on physical parameters of rock, especially the P-wave velocity and porosity. Many scientists, including Pickett [5], Milholand [6], Domenico [7], Thomsen [8], Han [9], Krief [10], Castagna [11] and Greenberg [12] have done very useful research in this area and various relationships have been developed and presented. These relations are valid for the saturated rocks with brine.
Gassman formulas have been introduced to extend these experimental formulas to other fluids contents. In 1986, Han offered empirical regression formulas for elastic waves in laboratory condition which would estimate the speed based on porosity and clay content. In 1989, Eberhart added the pressure parameter to Han’s equation for shale sand rocks. Years before, Tosaya and Nur [13] and Castagna et al. [11] presented empirical formulas for shale sand rocks based on velocity, porosity and clay parameters.
Other methods are artificial intelligence techniques such as neural networks and fuzzy logic [14–16]. Although their estimates are associated with less error, these methods also present a specific model for each different field, and the results from one field cannot be applied to other fields.
There are two methods to calculate the elastic coefficients. The first one is the static method (destructive) and the other one is the dynamic (non-destructive) method. In the static method, elastic parameters of rock are calculated from laboratory measurements such as the uniaxial compressive strength of cores. But in a dynamic method, assuming that rocks are elastic, the coefficients are determined from propagating shear and compressional waves in rock and measuring waves travel time, without damaging the rock [17].
Currently, there is no unique empirical formula or comprehensive theory that could be utilized to determine the elastic wave velocity and elastic coefficients at different environmental conditions, type of fluid and rock. In this paper, experimental data (elastic wave propagation velocity) has been gathered using a sample saturated with water and supercritical carbon dioxide at different reservoir pressure. Then while the common fluid (brine) was replaced by critical CO2, the elastic wave velocity values were calculated using Gassman formulas and Greenberg - Castagna empirical equations and the results were compared with direct laboratory observations.
2.2 Methodology
2.1.2 Estimating the Shear Wave Velocity
A major part of the seismic signal analysis in regards to rock physics models relates shear wave velocity to mineralogy and porosity. Rock physics analysis based on logs and cores and the relation of these to the geological model, leads to the establishment of a relationship between velocity and porosity. Formulation of the relation between rock velocity and rock