The Gun Digest Book of Rimfire Rifles Assembly/Disassembly. J.B. Wood
and lever link, be sure the pointed front arm of the lever link lies on top of the carrier guide pin.
Browning Semi-Auto 22
Similar/Identical Pattern Guns
The same basic assembly/disassembly steps for the Browning Semi-Auto 22 also apply to the following guns:
Browning Standard Auto Grade II
Browning Standard Auto Grade III
Browning Standard Auto Grade VI
Norinco 22 ATD
Remington Model 24
Remington Model 241
| Data: | Browning Semi-Auto 22 | |
| Origin: | Belgium | |
| Manufacturer: | Browning Arms Company, Morgan, Utah | |
| (Made for Browning by FN in Belgium) | ||
| Cartridge: | 22 Long Rifle | |
| Magazine capacity: | 11 rounds | |
| Overall length: | 37 inches | |
| Barrel length: | 19¼ inches | |
| Weight: | 4¾ pounds |
This neat little semi-auto rifle was first produced in 1914 by FN in Belgium. In 1922 production rights for the U.S. were leased to the Remington company, and it was made by them as the Model 24 and Model 241 until 1951. In 1956 a slightly altered version was introduced by Browning, and it was made for them at FN until 1974. From that time to the present, the gun has been made for Browning by Miroku of Japan. Through all of this time, the internal mechanism has been essentially unchanged. There are some minor differences in the extractor and cartridge guide systems, but the instructions will still apply.
Disassembly:
1. The takedown latch is located on the underside of the forend, at its rear edge. Push the latch forward into its recess in the forend.
2. Retract the bolt slightly, and turn the barrel assembly clockwise (rear view) until it stops. Then, remove the barrel assembly toward the front.
3. Remove the screw on the underside of the forend, and take off the forend downward.
4. Slide the takedown latch forward out of its base at the rear of the barrel. Caution: Two plunger-and-spring assemblies will be released, and must be restrained to prevent loss. The first will be the positioning plunger and spring at the rear of the latch, and the second will be the wedge-shaped plunger under the latch which bears on the barrel adjustment nut serrations. Ease both of these out, and take care that these small parts aren’t lost.
5. Remove the takedown latch base ring toward the rear. Unscrew the knurled barrel adjustment nut and remove it toward the rear.
6. Insert a finger through the trigger guard, place the thumb on the bolt handle, and retract the bolt to the rear while exerting forward pressure on the guard. The trigger group and bolt assembly can now be moved forward together and removed downward.
7. Pull the trigger to release the striker into the bolt, then move the front of the bolt upward out of the guard unit and ease it off forward. Caution: Both the bolt spring and the striker spring are under some tension, so take care that they don’t get away. Remove the springs and their guides from the rear of the bolt.
8. Remove the striker from the rear of the bolt.
9. Drifting out the cross pin at the lower front of the bolt will release the extractor retainer and allow removal of the extractor and its spring downward.
10. To remove the inner magazine tube, pull it out until it stops, then turn it 180 degrees to clear its side steps from the detents in the outer tube and take it out toward the rear.
11. Drifting out the locking cross pin at the head of the inner magazine tube will allow removal of the handle piece, spring, feed cable, and follower.
12. Use a very wide screwdriver or a special shop made tool to remove the nut at the rear of the buttstock, and its lock washer, and take off the stock toward the rear. The outer magazine tube can now be unscrewed from the rear of the receiver. Caution: Avoid gripping the tube too tightly and deforming it.
13. Swing the cartridge stop toward the inside wall of the receiver to clear its inner arm and lift it out of its pivot-hole in the roof of the receiver. It should be noted that on older guns that have seen a lot of use, the cartridge stop may fall out when the bolt and trigger assembly are removed, so be sure it isn’t missed and lost.
14. Removal of the cartridge guide spring in the top front of the receiver will release the cartridge guide to be taken out toward the front. To remove the spring, use a small tool to pry its rear loop from beneath its flange in